Blown-In Insulation in Converse, TX

Reaching the same R-value target takes noticeably more inches of fiberglass, which delivers about R-2.5 per inch, than cellulose at roughly R-3.7 per inch. Each material has trade-offs: cellulose packs denser and resists air drifting through the blanket, though it weighs more and settles more over time, while loose-fill fiberglass stays light, barely settles, and won't wick water if the attic ever leaks. Our crews read each product's coverage chart and blow to that material's own correct depth, because inch-for-inch the two simply are not equivalent.

Settling is the reason. Cellulose compresses more than fiberglass, and either way the blanket you see on install day sits lower six weeks later. So we deliberately install above the final R-target, planning the depth so the SETTLED blanket still meets spec once it compacts. A crew that blows only to the day-one target leaves you short after settling, and that quiet shortfall is one of the most common ways a loose-fill job under-delivers.

No, and that limit is worth understanding. Loose fill slows heat conducting through it, but air keeps moving right past it at top-plate gaps, recessed can lights, and every penetration in the ceiling plane. Blow it over an attic that was never sealed and the material just strains the air leaking by. Air-sealing is its own step and it comes first; the blown layer then handles conduction while the sealing handles leakage.

In most attics, yes. This is what we call a top-off: provided the existing layer is dry, intact, and free of mold or matting, loose fill drapes right over the old material and we add depth until the combined total reaches target. Where the old fill has been walked flat or crushed, we re-fluff or re-level it before blowing, so the fresh layer isn't resting on a dead compressed base.

Loose fill earns its keep by wrapping seamlessly around joists and wiring with zero gaps, and that only happens when it goes in at an even depth and the right machine density. Thin edges or under-fluffed sections turn into cold spots. Our process dams the eaves, dials in the blower density, and staples depth-marker rulers across the deck, which makes the installed inches a measurement you can read for yourself rather than a promise you have to take on faith.

Yes — our crews cover Converse's 3 ZIP codes across Bexar County, including Kensington Ranch, Stonebridge, Willow Run, plus the surrounding communities.

We offer same-week scheduling across Converse, booked by a real person in under two minutes, 7 AM to midnight every day.

Converse is fast-growing east-Bexar suburbia — Kensington Ranch, Stonebridge — dominated by newer prefab fireboxes. Cap and chase-cover service lead, with clay-liner work on the older stock near the city core. Either way, one cross-trained crew covers chimney, cap and vent in a single visit instead of three separate trades. Blown-In Insulation is part of keeping that local housing stock safe, efficient, and up to code.

Blown-In Insulation in Converse starts from $1,450, but the honest number depends on what a craftsman finds on site — we won't quote premium work blind. A CSIA-certified technician inspects the actual condition, then hands you an itemized, transparent written quote tied to the findings and built to one national standard. No teaser pricing, no surprises. Call (214) 444-8094 for a free, no-pressure Converse quote.

Yes — we run same-week and emergency blown-in insulation across Converse, scheduled by a real person 7 AM to midnight every day. For an active chimney hazard, call (214) 444-8094 and we prioritize Converse dispatch so a craftsman is on it fast.

Our Converse crew lives in and works the metro across Bexar County, including Kensington Ranch, Stonebridge, Willow Run — a certified, local blown-in insulation team genuinely near you, holding the same national craftsmanship standard on every job, not dispatched cold from another city. Call (214) 444-8094.